Where Should Workplace First Aid Kits Be Located? A Placement Checklist

A first aid kit can be fully stocked and still fail operationally because it is behind a locked door, hidden in a cabinet no one recognizes or separated from the work by stairs, gates or controlled areas. Placement should be tested as a response route, not settled by choosing a convenient empty wall.

Quick answer: Put workplace first aid kits where workers can reach them during every shift, identify them quickly and retrieve them without avoidable delay. Map actual work areas, barriers and shift access before choosing locations. Do not assume one mounting height or distance rule applies across Canada; check the governing jurisdiction.
White Ready First Aid case shown with a Federal First Aid Kits label
A store first aid kit image, not a placement demonstration or a kit specification for every workplace. Select against the applicable assessment.
Scope and review note: This checklist covers British Columbia, Alberta and workplaces governed by the COHSR. It does not summarize every province, territory or sector-specific federal regime. It addresses placement after the workplace has identified its required first aid services, attendants, equipment and kit contents.

Placement starts with the workplace assessment

Do not use this article to decide how many kits a workplace needs or which classification to buy. Start with the workplace first aid kit requirements guide, confirm the jurisdiction and complete the required assessment. The CSA first aid kit types guide explains type, size and edition when a CSA-based system applies.

Placement follows from that work. A facility may need a central service, kits in distinct work areas, or other arrangements based on its assessment. A second kit can reduce retrieval time, but adding boxes does not correct the wrong contents, missing attendants, poor communication or an inadequate transportation plan.

What official sources say about access and location

British Columbia

WorkSafeBC’s assessment process considers each workplace location, workers per shift, assigned hazard rating, ambulance access and barriers to first aid. Use that written assessment to decide how resources can be reached. Test separated areas and shift access instead of applying one Canada-wide distance rule.

Alberta

Alberta OHS Code section 179 requires the first aid resources covered by the Code to be at or near the worksite served and readily available and accessible during working hours. Supplies, equipment and kits must be clearly identified, and conspicuous signs must explain how to contact first aiders and where to find resources, unless signs are not reasonably practicable and workers are informed another way. Read the exact wording in Alberta OHS Code Part 11.

Workplaces covered by the COHSR

Canada Occupational Health and Safety Regulations section 16.5 requires at least one first aid station per workplace, subject to its stated exception. In a multi-storey building, employees must be no more than two storeys from a station. The station must be at or near the workplace, conspicuously signed and accessible during working hours. This COHSR two-storey rule should not be presented as a rule for all Canadian employers or every federally regulated sector. See the current COHSR section 16.5.

Walk the route before mounting a kit

Use the busiest normal shift, not an empty building tour. Start where injuries could reasonably occur and walk toward the proposed first aid location. Repeat from separated rooms, mezzanines, yards and temporary work areas. Record what slows access.

  • Doors and permissions: Is a badge, key, supervisor or reception access needed?
  • Physical barriers: Are there stairs, locked gates, machinery aisles, slippery areas or routes unsuitable for moving an injured person?
  • Shift changes: Does the location remain open during nights, weekends, cleaning shifts and breaks?
  • Visibility: Can a new worker or visitor recognize the sign from the normal approach?
  • Environment: Could moisture, dust, temperature or routine impacts damage the case or contents?
  • Communication: Can workers summon the first aid attendant from the area served?

If the test depends on someone “usually being there,” treat that as a failure until the access process is formalized. Likewise, a sign pointing into a locked room does not make the supplies accessible.

Store graphic showing a first aid kit and its illustrated supplies
Store kit illustration. Verify current itemized contents against the site’s approved specification before purchasing.

Use this site map worksheet

Draw a simple floor or site map. It does not need to be architectural. Mark work areas, proposed kits or stations, first aid facilities, attendant bases, phones/radios, controlled doors, stairs, gates and routes used to move an injured worker. Then complete one row for every proposed location.

Workplace first aid placement worksheet
Field What to record Pass question
Area served Rooms, floor, yard, crew or temporary zone. Does this match the documented assessment?
Jurisdiction/source Authority, rule/guideline and assessment version. Was the current source checked?
Access by shift Day/night/weekend access and key/badge needs. Can workers retrieve it during all working hours?
Route barriers Doors, stairs, gates, hazards or seasonal obstacles. Is there a usable route without avoidable delay?
Signage Sign position, sight line and contact instructions. Can an unfamiliar worker find help?
Protection Moisture, dust, heat/cold, impacts and housekeeping risks. Will the selected container protect its contents as documented?
Owner Name/role responsible for inspections and access. Is responsibility assigned for every shift?
Test result Date, shift, start point, issue and corrective action. Was placement tested rather than assumed?

Placement mistakes worth correcting

Putting every kit in the office. The office may be easy to monitor but distant from production, a warehouse yard or a second floor. Test it against all areas and shifts.

Locking supplies to control shrinkage. Inventory control matters, yet emergency access cannot depend on locating one key holder. Choose a control method that preserves required access.

Using one placement rule across every site. A federal multi-storey rule, WorkSafeBC guideline or Alberta requirement has a defined jurisdiction. Copying it into a national policy without scope creates false certainty.

Letting the kit migrate. Portable kits need a named return location. Add the location to opening checks, inspections or shift handovers.

Ignoring changes. Renovations, new secure doors, changed shifts, temporary projects and relocated teams can invalidate a good location. Review the map when work changes and whenever the governing assessment requires review.

Close the placement check

  1. Confirm the jurisdiction and approved first aid assessment.
  2. Mark every work area and the resources intended to serve it.
  3. Walk and time representative routes, then compare the observed time with the applicable requirements and workplace assessment.
  4. Fix access, signage, environmental protection and communication gaps.
  5. Orient workers to kit locations and how to call for help. CCOHS specifically identifies this knowledge as part of workplace preparedness.
  6. Record the test, corrective action, owner and next review trigger.
Buying after the assessment? Use the selection guide to compare formats, then browse the First Aid Kits collection. Verify each exact product against the documented workplace requirement; a product category does not establish compliance.

Sources and editorial note

Official sources checked 17 November 2026: WorkSafeBC first aid requirements and WorkSafeBC assessment process; Alberta OHS Code Part 11; COHSR section 16.5; and CCOHS First Aid—General. This is general information, not legal, compliance or medical advice.


Leave a comment

Please note, comments must be approved before they are published

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.


Featured product

Featured product

Featured product